Site Information

 Loading... Please wait...

BGAN Firmware Upgrades

iSavi (Isat Hub) version R02.0.1

  • The enhancements and bug fixes included in this release (compared to the earlier firmware release R02.0.0) are the following:
    • Added satellite selection.
    • Stability improvements for the SIP server.
    • Added alert message when wrong password is entered for the factory reset through Web MMI.
  • Download Firmware upgrade now: Version: R02.0.1

 

Safari version R2.0.0

  • The following are the new features included in this firmware release (compared to the firmware release R01.2.0):
    • Included updated BGAN protocol stack supporting MEAS satellite region
    • Included support for XL-band
    • Included antenna SMART searching feature (Garage Mode)
    • Included serial device feature
    • General Web MMI improvements
  • Download Firmware upgrade now: Version: R2.0.0

 

Explorer 325/727 V1.26

  • Subject: Please be informed that a new software version 1.26 for the following Cobham SATCOM products has been released:
    • SAILOR 500 FleetBroadband TT-3740A
    • SAILOR 250 FleetBroadband TT-3742A
    • SAILOR 150 FleetBroadband TT-3744A
    • SAILOR Fleet One TT-3744A-00581/00591
    • EXPLORER 727 TT-3722A
    • EXPLORER 325 TT-3721A
  • Priority: MEDIUM: It is recommended to apply this change / initiative to all units in stock. For units sold it is recommended to apply this change / initiative next time the system(s) is inspected.
  • Major changes from software version 1.25 to version 1.26:
    • Admin login now working using HTTP cookie in web browsers
    • MultiVoice adapted for support of a future Inmarsat network change
    • The "Check for software updates" service in the web interface has been closed
    • Security fixes
    • Bug-fixes
    • General improvements
  • Download Firmware upgrade now: Version: 1.26

 

Explorer 510 V1.04

  • Priority: MEDIUM: It is recommended to apply this change / initiative to all units in stock.
    For units sold it is recommended to apply this change / initiative next time the system(s) is inspected.

    Changes from software version 1.03 to version 1.04:
    • New Features:
      • Terminal Watchdog (TWD) - With a scheduled interval, the TWD will perform a terminal health check. The TWD verifies:
        • Valid System Time
        • Valid position
        • Attachment to BGAN network
        • Successful TWD initiated PDP setup
        • Successful ping response via TWD initiated PDP (optional)
      • Non-Inmarsat BGAN SIM cards
        • Support for Non-Inmarsat BGAN SIM cards in the terminal.
      • M2M Functions
        • Support for M2M SMS and AT commands similar to the EXPLORER 540.
        • Note the following limitations:
          • The E510 does not support M2M BGAN SIM cards.
          • The E510 does not support OTA SW upgrade from the Inmarsat FUP server, but 3rd party FTP server is supported.
          • The E510 does not support M2M Power Save and corresponding wake-up functions.
      • SMS messages controlled by the AT shell
    • Updated Features:
      • Updated status for PPPoE controlled PDP
        • The Web interface and Local display will now show status for PPPoE controlled PDPs.
      • Updated status for AT-cmd controlled PDP
        • The Web interface and Local display will now show status for AT-cmd controlled PDPs.
      • Updates to the Web interface
        • Minor updates to the Web interface; New “Advanced LAN” tile and some updates to tile names and structure.
      • Cellular data sessions logged
        • Cellular data sessions are included in the call log and the total counters.
      • Pointing Sound volume control
        • Pointing sound volume setting in Web Terminal settings.
    • Important Bug fixes:
      • Applying repeated AT commands without a delay could cause the terminal to reboot.
  • Download Firmware upgrade now: Version: 1.04

 

Explorer 540 M2M V1.04

  • Major highlights of this release:
    Note: This is a minor bugfix/update release based on the previous SW 1.03 baseline.
    • New Features:
      • Support for the EXPLORER Connect App. The EXPLORER Connect App for iOS and Android smartphones can now be used for the E540 with a wireless Access Point connected.
        • Please note:
        • The EXPLORER Connect App Satellite Phone can not be used if the E540 is running in M2M mode.
        • The “Pointing” and “Dashboard” App menu functions are not applicable for use with the E540.
    • Updated Features:
      • Power Save can now be controlled with the General Purpose Input (GPI) pin 1.
        • If Power Mode is enabled two modes can be used to enter Power Save: “Idle time” mode or “GPI” mode.
        • The function of the “Idle time” mode is unchanged compared to the previous release.
        • In “GPI” mode the E540 will enter or leave Power Save controlled by an Active or Inactive signal on GPI pin 1.
        • Note that in “GPI” mode the E540 will enter Power Save as soon as the GPI pin 1 becomes Inactive without other conditions (except for a possible “Grace” period) as opposed to the “Idle time” mode, where more condition may have to be fulfilled before the E540 enters Power Save.
        • In order to prevent the E540 to enter Power Save caused by misconfiguration the E540 has implemented a “Grace” period. First time the E540 is signalled (by Inactive GPI pin 1) to enter Power Save it will delay the entry into Power Save until the specified “grace” period has elapsed. The “Grace” period is active every time the E540 starts–up following a: Power cycle, a terminal reboot, TOD caused wake-up or other non-GPI requested start-up. The Grace period must be between 3 – 60 min. (Note that if the Inactivity signalling is removed before the grace period has elapsed a new grace period will start next time the Inactive signalling is set).
        • If the E540 has entered Power Saved caused by an Inactive signal on GPI pin 1 it can optional leave the Power Save if a Time-Of-Day value has been specified and reached. If the GPI pin 1 signal is still Inactive the E540 will only stay out of Power Save for the specified Grace period.
    • Notes about known Power Save limitations in “GPI” mode:
      • AT commands for Power Save settings: The AT (and SMS ATCO) command “AT_IPWSAVSCHD” can only be used to control Power Save when operating in “Idle time” mode. Do not us the “AT_IPWSAVSCHD” command if the Power Save mode via the Web settings has been specified as “GPI” mode, as it can cause confusing Power Save settings.
      • SW update: If the E540 is conduction a SW update (local or Over-The-Air) requesting the E540 to enter Power Save by GPI Inactive signalling may (depending on the timing) abort the SW update process. It is therefore not recommended to change the GPI signalling to Inactive during an ongoing SW update.
      • Terminal Watchdog: If the Terminal has entered Power Save due to GPI in 1 signal being inactive and the Terminal Watchdog wakes the terminal in order to execute its health check, the terminal will not enter Power Save again before the GPI pin 1 signal has gone Active and Inactive again.
    • Important User related bug fixes:
      • Support for voice call when a non-M2M E540 is operating in dual (BGAN & Cellular) mode. (80537).
        • Note: Voice service is still not allowed in M2M mode.
      • Corrected implementation of PAP authentication. (79064).
        • Handling of PAP authentication with empty password.
      • Handling of corrupted “_” character in SMS M2M commands. (79318).
        • Handling of corrupted “_” character observed from some GSM mobile network in cooperation with the BGAN network.
      • Delaying setup of configured PDPs until completion of the auto-install mode. (79079).
        • Setup of pre-defined PDPs are now delayed until the auto-install (including PDP verification) is completed.
  • Download Firmware upgrade now: Version: 1.04

 

Explorer 710 V1.08

  • Priority: MEDIUM: It is recommended to apply this change / initiative to all units in stock.
    For units sold it is recommended to apply this change / initiative next time the system(s) is inspected.

    Changes from software version 1.07 to version 1.08:
    • New Features:
      • Terminal Watchdog (TWD) - With a scheduled interval, the TWD will perform a terminal health check. The TWD verifies:
        • Valid System Time
        • Valid position
        • Attachment to BGAN network
        • Successful TWD initiated PDP setup
        • Successful ping response via TWD initiated PDP (optional)
      • Non-Inmarsat BGAN SIM cards
        • Support for Non-Inmarsat BGAN SIM cards in the terminal.
      • M2M Functions
        • Support for M2M SMS and AT commands similar to the EXPLORER 540.
        • Note the following limitations:
          • The E510 does not support M2M BGAN SIM cards.
          • The E510 does not support OTA SW upgrade from the Inmarsat FUP server, but 3rd party FTP server is supported.
          • The E510 does not support M2M Power Save and corresponding wake-up functions.
      • SMS messages controlled by the AT shell
    • Updated Features:
      • Updated status for PPPoE controlled PDP
        • The Web interface and Local display will now show status for PPPoE controlled PDPs.
      • Updated status for AT-cmd controlled PDP
        • The Web interface and Local display will now show status for AT-cmd controlled PDPs.
      • Updates to the Web interface
        • Minor updates to the Web interface; New “Advanced LAN” tile and some updates to tile names and structure.
      • Cellular data sessions logged
        • Cellular data sessions are included in the call log and the total counters.
      • Pointing Sound volume control
        • Pointing sound volume setting in Web Terminal settings.
    • Important Bug fixes:
      • Applying repeated AT commands without a delay could cause the terminal to reboot.
  • Download Firmware upgrade now: Version: 1.08
LiveChat